awards

Derby Mom 360: Mario Kart Award Ribbons

Mario Kart Party: Award Ribbons with Printables

Here’s what you’ll need:Derby Mom 360: Mario Kart Award Ribbons
Construction Paper: Blue, Red and Yellow (2 strips of 2.5”x12” each color)
Cardstock (3 strips of 2” x 11”)
Ribbon (1” x 24”)
Hot Glue Gun
Printable Centers (see below) or homemade inserts of your choosing

To begin, cut two pieces of construction paper that are 2.5” wide x the longest length. My paper was 12” but whatever you have is fine. I wanted pretty large awards. If you’d like yours to be smaller, cut the width of these two strips narrower. I cut out two strips of all three colors.

Derby Mom 360: Mario Kart Award RibbonsNext you’ll want to cut out some strips of cardstock. I liked the look of the brown more natural sheets but you could use anything. I cut these 2” wide. Again, just cut them the length of your paper. My paper was 11.5”. You’ll just need one strip for each ribbon, so three total for this project.

Then you’ll start crimping your construction paper, meaning that you’ll want to fan fold it back and forth. There’s no exact size here. I found that I liked the look of a little tighter fold but you can do whatever you’d like here. Once you start folding one color, you’ll try to keep the size of your folds the same size each time for both strips.

Derby Mom 360: Mario Kart Award RibbonsDerby Mom 360: Mario Kart Award RibbonsOnce you’ve fan folded it all, you’ll want to glue the two ends together on each side for you get a fully connected cylinder. You could use any glue or tape here but I find a glue gun easiest for the rest of the project so I used that.

The next bit is probably the trickiest portion of this award project. You’ll want to bring on edge of the cylinder all together and lay it flat. The other edge will fan out and become the outside of the ribbon. It took both hands at first to keep it held in that position. Then once you have it properly gathered, you’ll grab your glue gun and put a good blob of hot glue in the center. You’ll need to keep holding the starburst in place while the glue dries. I just held it and blew on it for a about two minutes. After my first award, I realized I could wedge heavier objects on a couple sides to keep it from moving while it dried. Whatever works, you just want the glue to be hard before you release it.

While that is drying, you can prep your inserts. I made mine kind of funny and full of inside jokes for my group of friends. I have a more generic one here that is more likely to meet your needs. Just cut these out and they will serve as your center inserts. I chose to print them on cardstock so the paper would be stiffer to hold up to the hot glue.

Derby Mom 360: Mario Kart Award Ribbons

Next you’ll want to hot glue the insert to the appropriately colored construction paper starburst. I did First (Grand Champion sounded more regal) in blue, Second in red and Third in Yellow. I flipped my starburst over and found the side without the glue glob to be more flat and easier to affix the center circle nice and flat. I hot glued in the center of the circle and then much more thinly near the perimeter so it would be on snuggly but not show any lumps of glue.

Derby Mom 360: Mario Kart Award RibbonsDerby Mom 360: Mario Kart Award RibbonsMaro-Kart-Awards-5Then the last part is to prep and affix the lower ribbon portion. I folded my cardstock at an angle to look like ribbon. Then I cut two strips of ribbon, slightly longer than each piece and glued them into place and let them hang over the end. Once that glue dried, I cut out a triangle on the bottom to give them a nice finished look. I used about 2 feet of white 1” wide ribbon but you could really use any scraps you have lying around.

Derby Mom 360: Mario Kart Award RibbonsLastly, I laid down a good portion of glue at the folded end and affixed the back of my starburst to it. I head it in place for a bit until the glue started to set. That’s it! You have one beautiful homemade ribbon. I made one first to get the hang of it and then assembly lined the rest of them doing each step at the same time.

I found some cute Mario Kart trinkets at Ross and affixed each award to the prize as a “trophy” for the tournament top finishers. I have a very competitive group of friend and I felt like the awards made it so there was more on the line. There are prizes and titles to be won or lost! Makes the stakes higher.

I’d love to see how yours turned out. Post to the Flickr Group to share your creations.